BAUMER工业相机LXG-500M现货报价

Digital Monochrome Matrix Camera, Dual Gigabit Ethernet

Sensor Information

Image Pre-Processing

Gamma Correction Gamma (0.1 … 2 | available if LUT is enabled)

LUT Luminance (12 bit)

Color Models Mono

Color Tolerance Only on Color Cameras

Color Processing Only on Color Cameras

Color Adjustment Only on Color Cameras

Binning 1 or 2 (Horizontal and Vertical)

Decimation 1 or 2 (Horizontal and Vertical)

Image Flipping Horizontal, vertical

Defect Pixel Correction via Defect Pixel List with up to 3000 Pixel Coordinates

Process Synchronization

Modes Free Running, Trigger

Free Running Continuous or

Adjustable Acquisition Frame Rate (0.01 … 3400 Hz) Trigger Sources Hardware, Software, ActionCommand, All or Off Trigger Delay 0 ... 2 sec, Tracking and buffering of up to 512 triggers Sequencer Characteristics up to 128 sets of parameters, up to 65536 loop passes,

up to 65536 repetitions of sets of parameters, up to 65536 images per trigger event

Sequencer Parameters Exposure Time, Gain Factor, Output Line, ROI Offset x,

ROI offset y External Flash Sync via Exposure Active

tdelay flash ≤ 3 µsec, tduration = texposure + 18 µsec

Digital I/Os

Lines Input: Line 0, Output: Line1, Line 2, Line 3

Circuit Times Output:    tON  = typ. 2 µsec tOFF = typ. 30 µsec Output Sources Off, ExposureActive, ReadoutActive, FrameActive,

TriggerReady, TriggerOverlapped, TriggerSkipped,

Line 0, UserOutput{1,2,3}, Timer{1,2,3}Active, SequencerOutput{0,1,2}

Line Debouncer Low and high signal separately selectable

Debouncing Time 0 … 5 msec, Step Size: 1 μsec

Interfaces and Connectors

Data Interface (1/2) Gigabit Ethernet    Transfer Rate  1000 Mbits/sec

Fast Ethernet Transfer Rate    100 Mbits/sec

Connector: 8P8C Modular Jack (RJ45)

screw lock type

Pin Assignment:    1 – MX1+ 5 – MX3-

2 – MX1- 6 – MX2-

3 – MX2+ 7 – MX4+

4 – MX3+ 8 – MX4-

Power and Process Interface

Connector: SACC-DSI-M8MS-8CON-M8-L180 SH

Assignment: 1 – OUT3 (line3) 5 – IO Power VCC

2 – Power VCC 6 – OUT1 (line1) 3 – IN1 (line0) 7 – GND

4 – IO GND 8 – OUT2 (line2)

Mechanical Data

Optical Data

 Electrical Data

Power Supply (ext.) VCC: 12 … 24 V DC ± 20%

I: 420 … 830 mA

Power over Ethernet Class 0 device

VCC: 36 … 57 V DC

I: 250 mA @ 48 VDC

Power Consumption approx. 10 W @ 24 VDC and 5 fps

approx. 12 W @ 48 VDC (PoE) and 5 fps

Digital Input UIN(low) : 0.0 … 4.5 VDC

UIN(high) : 11.0 … 30.0 VDC

IIN : 6.0 … 10 mA

min. Impulse Length: 2.0 μsec Trigger Delay out of treadout:   110.0 μsec max. Trigger Delay during treadout: 110.0 μsec

Digital Output UEXT: 5 … 30 V DC IOUT: max. 50 mA

LED Signalling

Camera LED Green on Power on, link good Green blinking Power on, no link Red on Error

Red blinking Warning

Yellow Readout active

RJ45 LEDs (1/2) Green on Link on Green blinking Link activity Amber on GigE speed

GigE Vision® Features (in compliance with GigE Vision® 1.2)

Events

Transmission via Asynchronous Message Channel

GigEVisionError, HeartbeatTimeOut, EventLost, EventDiscarded, Line{0,1,2,3}RisingEdge, Line{0,1,2,3}FallingEdge, Action1, ExposureStart, ExposureEnd, FrameStart, FrameEnd, TriggerReady, TriggerOverlapped, TriggerSkipped, Timer{1,2,3}End, Phy{0,1}Up, Phy{0,1}Down

Frame Counter up to 232

Payload Size 4 … 47551680 Byte

Transmission Delay 0 .. 232-1 Ticks (1 Tick = 8 nsec)

Timestamp 64 bit

Packet Delay 0 .. 232-1 Ticks (1 Tick = 8 nsec)

Packet Resend Resend Buffer: 408 MB (2 Images)

GenICamTM Features (in compliance with SFNC 2.1.0)

Vendor Specific Features

Factory Settings after Start-Up